Off- Engine Chevy 3L Block Only System

Product Image Display
Product Code
MRM-5345
Weight
38.00
Price
$1036.00

CONVERSION KIT FITS
This conversion kit fits most Chevy 3.0L 4-Cyl engine conversions made by the major marine engine manufacturers. See space requirements to confirm that it will fit within the engine compartment. 

COOLING SYSTEM TYPE
Off-engine remote mounted. Block only. (The engine block protected by freshwater system; the exhaust manifold and exhaust elbow remain on raw water system.) 

CONVERSION KIT
Kit includes heat exchanger, heavy-duty translucent plastic expansion tank plus all other components necessary to complete conversion. Some components from engine are reused. Heat Exchanger and Brackets are finished in black. Hose clamps are all stainless steel.

HEAT EXCHANGER
Heat exchanger is shell and tube type with special high capacity design. All copper alloy construction made to the highest industry standards. Includes dual demountable end covers for easy clean out. 

SPACE REQUIREMENT
Before purchasing this system, make sure there is enough room in the engine compartment to accommodate the heat exchanger, expansion tank, and necessary components. Heat exchanger is 3.69" diameter x 17" overall length. Heat exchanger should be mounted as close to the front of the engine as possible. The mounting bracket is included with the kit. Note: The heat exchanger must be below the level of the filler neck on the thermostat housing. The heat exchanger may be mounted on any horizontal or vertical surface. Expansion tank is mounted close to level with the filler neck. Required space is 4" x 6" x 8 1/2" the opening or closing of the hatch. Do not drill into fuel tanks, water tanks, or any other critical areas. Do not contact any belts or fuel lines. 

COOLING SYSTEM CAPACITY
The heat exchanger will maintain coolant temperatures in the 160-170°F range using 160°F thermostat included in kit. The system has a cooling capacity safety margin higher than industry standards. 

HEATER SYSTEM HOOKUP
Heaters such as galley water heaters and cabin heaters are not recommended on four-cylinder engines because they may over-cool the engine. 

INSTALLATION TIME
Average installation time is approximately two hours, assuming new engine and normal accessibility. Allow additional time for filling and testing. Installation skills are typical of most do-it-yourself boat owners. Complete illustrated installation instructions are included in kit. 

WARRANTY
Two year warranty. For complete details see Limited Warranty for Fresh Water Cooling Kits document enclosed with your kit and located on policies page of our website.

PRICE
Trade and volumbe discounts available. Buy through your dealer or direct using Visa, Mastercard, AM Express, UPS COD, or money order.

This conversion kit fits most Chevy 3.0L 4-Cyl engine conversions made by the major marine engine manufacturers. See space requirements to confirm that it will fit within the engine compartment. 

COOLING SYSTEM TYPE
Off-engine remote mounted. Block only. (The engine block protected by freshwater system; the exhaust manifold and exhaust elbow remain on raw water system.) 

CONVERSION KIT
Kit includes heat exchanger, heavy-duty translucent plastic expansion tank plus all other components necessary to complete conversion. Some components from engine are reused. Heat Exchanger and Brackets are finished in black. Hose clamps are all stainless steel.

HEAT EXCHANGER
Heat exchanger is shell and tube type with special high capacity design. All copper alloy construction made to the highest industry standards. Includes dual demountable end covers for easy clean out. 

SPACE REQUIREMENT
Before purchasing this system, make sure there is enough room in the engine compartment to accommodate the heat exchanger, expansion tank, and necessary components. Heat exchanger is 3.69" diameter x 17" overall length. Heat exchanger should be mounted as close to the front of the engine as possible. The mounting bracket is included with the kit. Note: The heat exchanger must be below the level of the filler neck on the thermostat housing. The heat exchanger may be mounted on any horizontal or vertical surface. Expansion tank is mounted close to level with the filler neck. Required space is 4" x 6" x 8 1/2". The expansion tank must be mounted as close to the engine as possible. The mounting locations should not hinder the opening or closing of the hatch. Do not drill into fuel tanks, water tanks, or any other critical areas. Do not contact any belts or fuel lines. 

COOLING SYSTEM CAPACITY
The heat exchanger will maintain coolant temperatures in the 160-170oF range using 160oF thermostat included in kit. The system has a cooling capacity safety margin higher than industry standards. 

HEATER SYSTEM HOOKUP
Heaters such as galley water heaters and cabin heaters are not recommended on four-cylinder engines because they may over-cool the engine. 

INSTALLATION TIME
Average installation time is approximately two hours, assuming new engine and normal accessibility. Allow additional time for filling and testing. Installation skills are typical of most do-it-yourself boat owners. Complete illustrated installation instructions are included in kit. 

WARRANTY
Two year warranty. For complete details see Limited Warranty for Fresh Water Cooling Kits document enclosed with your kit and located on policies page of our website.

PRICE
Trade and volumbe discounts available. Buy through your dealer or direct using Visa, Mastercard, AM Express, UPS COD, or money order.